FAQs
How should I store my Extra VitaBead Diffusers?
Store your Extra VitaBead Diffusers in a cool and dry area. As long as they aren't exposed to excessive heat or moisture, the Extra Diffusers will last until the next time you need them. There is no storage expiration date.
Learn moreCan I put my DYLN Bottle in the freezer to cool it?
We do not recommend putting your DYLN Bottle in the freezer. Water expands at freezing temperatures and may affect the structural integrity of the Bottle. Instead, we recommend putting ice cubes into your DYLN Bottle to keep the water cold.
Learn moreHow to clean the DYLN Bottle?
To clean your DYLN Bottle, first remove the Diffuser from your bottle. The inside of the bottle and the cap can be cleaned warm soapy water—preferably plant-based soap. Let the bottle and cap air dry for the best results before using again. Handwash the Diffuser with warm water without any soap. For best results, air dry your Diffuser before inserting back into your bottle. Please ensure to change your Diffuser every 300 liters or every three months, whichever comes first. You can use a dishwasher to wash the DYLN bottle and its accessories. Please make sure to remove the Vitabead diffuser first.
Learn moreRemoving and inserting the VitaBead Diffuser
*Please note: There are two outward 'dots' on the outside of the Diffuser, which the Tool will grab onto. These Dots are at the TOP of your Diffuser and should attach to the Tool. Please ensure you correctly insert the Diffuser into your Tool before reinstalling the Diffuser in your DYLN Bottle.
Learn moreHow do I know when to replace my Diffuser?
The easiest way to know when to replace your Diffuser is by registering your DYLN Bottle here. Once registered, we will send you an email reminder when it's nearing time to replace your Diffuser.
Learn moreWhat kind of water can I use with my DYLN?
We recommend only using purified or filtered water since the VitaBead Diffuser does not filter water. However, any water you consider safe to drink, you may use with the DYLN Bottle. For example, your tap water quality may be a different drinkable standard quality depending on where you live. The DYLN Bottle will enhance any water you add to it, however, it will not filter water.As for water temperature, we do not recommend using hot or boiling water as it will decrease the lifespan of the VitaBeads. Using warm, room temperature or cold water is fine.
Learn moreActivating the DYLN Diffuser
Before first use we recommend removing the VitaBead Diffuser and rinsing it for 20 seconds. Then soak it in warm water for 20 minutes, followed by letting it air dry completely overnight. Wash the bottle separately with warm water and plant-based soap if desired. Once dry, insert the Diffuser back into the bottle and you're ready to go! Please Note: Because of the living Nature of the VitaBeads, there will be pressure buildup within the DYLN Bottle. You may receive an occasional refreshing mist of water while opening. During the first two weeks of use, be sure to loosen the cap every few hours to release the pressure. Repeat these instructions each time you replace with a new Diffuser.
Learn morePreparing your DYLN Bottle (Before first use)
Get Started With Your DYLN Bottle! Activate Your Diffuser You should find your Diffuser attached to the Diffuser Removal Tool inside a cloth pouch inside the bottle. Remove the Diffuser from the tool, then rinse it under warm water for about 20 seconds. Soak the Diffuser in a glass of warm water for about 20 minutes. Remove the Diffuser from the glass, briefly rinse it again and then shake off any excess water. Let the Diffuser sit out overnight (or at least 8 hours) so the VitaBeads can air-dry completely. While the Diffuser is soaking and air-drying, wash out your bottle and cap with water and soap. Be sure to rinse out all of the soap. Attach the Diffuser to your Bottle Be sure to let the VitaBeads air-dry completely before attaching the Diffuser to the bottle. Attach the middle piece of your tool so the tool can reach the bottom of the bottle. Attach the Diffuser to the tool by fitting the L-shaped grooves on the tool over the two bumps on the top side of the Diffuser, then twist slightly to lock together. Be sure the Diffuser is the right way up. The top side has two bumps near the edge, and the bottom side has four tabs near the edge. Insert the Diffuser into the bottle and line it up with the Diffuser holder at the bottom of the bottle. Push down on the tool firmly to click the Diffuser into the Diffuser holder. Lightly twist the tool counterclockwise so it unlocks from the Diffuser, then remove the tool by pulling straight up. Register Your Bottle Head to www.dyln.co/register so you can register your new DYLN and keep track of the Diffuser usage. It's the easiest way to know when to change your Diffuser so you're never without alkaline antioxidant water!
Learn moreCan I add fruit or essential oils to my DYLN Bottle?
Many of our customers add slices of lemon to enhance the water flavor and some even use essential oils. In doing so, however, we just recommend that you clean your DYLN Bottle more often as it is designed to be just used with filtered or purified water. If you want to play it safe, you can alkalize water in the DYLN Bottle then move it to a different container and add the essential oils there. Water that is alkalized in the DYLN Bottle will remain alkaline for up to 3 days after being moved to a different container.
Learn more